Parting Out My 69 Coupe

[JP302Pony69]

Hey guys, About two years ago I bought a 69 coupe and was intending to restore it. The more I got into the project the more rust I found. It needs new front rails on both sides, floors, quarters, rear rails and trunk floors, and the roof needs to be repaired. Right now the car is completely stripped and one of the front frame rails is cut out. The car was just about complete when i got it and i have a lot of parts that are in good shape, it's too bad the body and frame are in such poor condition. It has a 302 with a c-4 transmission. The engine is mostly dissasembled and would need to be rebuilt but it was running before it came out of the car. The transmission was leaking fluid from the pan but shifted fine. I have most of the interior parts, including the lower dash and the guage cluster which i cleaned up and put new lenses in. It was a vynal top car and i have the trim moulding, but i believe one of the studs is broken off on one of the small side pieces. If you have any part requests feel free to message me or reply and I will be happy to see what I can do.

[lagalaxy8]

Looking for any of the woodgrain parts for the console, also need a window knob.

[JP302Pony69]

I didn't have the woodgrain dash as as option, i'll take a look for the window handle i should have them, are you looking for the front or rear window handle?

[Pakrat]

Sorry to hear the scale of the project took a turn on you for the worse, sounds like this one has been in New England all it's life. So I take it you will not be looking for a better project car to swap the parts to and stay in the hobby then?

Where in RI are you anyway? I spent the bulk of my life growing up in Pawtucket.

[JP302Pony69]

I would love to be able to find another car, but I'm at college and don't have the money to do so unless i could find another car in better shape for not much money. The car it taking up space in my parents garage and I really hate to get rid of it but that is what it is coming down to. I hope once i graduate i will be able to try again and find another project to work on.

Home is in Lincoln, but i go to school in Springfield, MA.

[lagalaxy8]

Nevermind on the knob, found it under the seat :)

But looking for a pass side horn, and both rear back up lights with lens
also looking for the "chrome" part that sits under the grille (I could get a pic if needed)

[JP302Pony69]

Allright, I have both horns, is the pass side the high or the low? As for the back up lights they are very pitted, and I don't have the chrome uner the grille.

[369coupes]

does it happen to have tinted glass? what color interrior i need black A pillar moldings and the hood molding and lower grille molding (thin) hows the front bumper?

[JP302Pony69]

Doesn't have tinted glass....Black interior, i do have the a-pillar moldings but i can't remember if they were cracked at all, i'll take a look and met you know. No lower grille molding and the front bumper is in bad shape

[lagalaxy8]

Still have the steering wheel?

[JP302Pony69]

I have the wheel that was on it but it's not factory.

[369coupes]

ok thanks , is the front bumper straight and just rusted? could it be rechromed? and does it happen to be a manual steering car? if it is id be interested in the pulleys and the center link and anything else to convert mine from power to manual steer

[JP302Pony69]

When i got the car before i took the bumper off it looked like it had been in a small front end accident so it's not completely straight. It is also a power steering car.

[lagalaxy8]

I have a straight bumper I might be interested in getting rid of, I just bought aftermarket ones.

[369coupes]

lagalaxy8, if you decide to let me know thanks

[krisfrego]

Are you interested in selling the whole car as is? Can you send me more photos to krisfrego@verizon.net. Thanks Kris

[lagalaxy8]

Yep let me know if you are interested. I just took it off last night. It's really in good shape. I wish I wouldn't have bought a new one now.

[lagalaxy8]

Turnsignal arm
radio
radio trim pieace
front valance
rear valance
you don't have the chrome part that is under the grille?

[JP302Pony69]

I think i have the turnsignal arm and the radio trim piece but i'm not sure what kind of shape they are in.

[JP302Pony69]

Next weekend I will be back in RI for a bit since it's the end of the semester. I'm going to go through the stuff i have and get the parts together. If anyone else has any requests let me know. Thanks.

[Burn]

PM sent!

[Solo2]

Sent another PM

[JP302Pony69]

For some reason I didn't get either of the PM's

[Solo2]

Sent third PM

[Pakrat]

I attempted to send you a PM too, don't know if you got it and you don't accept outside emails so I don't know how else to contact you. Anyway, I am going to be in the Attleboro and Cumberland areas next weekend and thought maybe if you were around I could arrange to stop by and look it over to see what I could use?

[Hemi Hunter]

Do you have the rear taillight wiring harness?

[jaydear]

Would it happen to have the oil/ transmission fluid cooler? I am looking for one for my 69 mustang. Thanks.

[JP302Pony69]

I do have the taillight harness but it's not in good shape and it did not have the oil/tranny cooler. Sorry for the delay everyone

[d.reese]

Looking for a am /fm radio, any luck here?

[JP302Pony69]

Nope no luck there either

[stangme]

would you happen to have the shift rod that connects the floor shifter to the tranny? I am looking for one and would also be interested in what you would want for the C4 if you haven't gotten rid of it yet, thanks.

[rangerdoc]

Does it have a 2bbl? I'm looking for parts from the left side of the carb; dashpot, linkage connector and bracket.

[JP302Pony69]

I'm pretty sure i have the shift rod still attached to the tranny. I still have the c4 as well, PM me an offer for the rod and the tranny. I would need to check on shipping to WA as well. Do you need the bellhousing too?

As for the carb It has a holley 600cfm 4bbl

[Blich123]

Are the headlight buckets in good shape...I need one for the passenger side that has all tabs not broken and the cast is not dented. If they are both good I would take them both. PM me a cost if they are...thanks

[R4K]

What kind of wheels and tires do you have on there?

[JP302Pony69]

The wheels are old steel aftermarket wheels, they're pretty rusty. The tires look brand new but it hasn't been on the road since '97 so i wouldn't trust them.

[mid-tn-mustang]

hi, i was wondering if you might have the hood catch that attaches to the underside of the hood. thanks
Chris

[JP302Pony69]

I think I do, it's just the part that bolts onto the underside of the hood that the latch catches to hold the hood down, right?

[Infinity]

do you have the kick panels? I need both sides. They don't need to be perfect.

Josh

[JP302Pony69]

I did have the kick panels, I will take a look for them this coming weekend and get back to you.

[mid-tn-mustang]

Hi, thanks for getting back with me on the hood latch catch. Do you also have the brace that runs vertically between the upper and lower radiator suppor that the c lookking brace attaches to.

[JP302Pony69]

I think I have that too but if i can remember right it was slightly bent....i'll take a look and get back to you this weekend. I'll take pictures of both parts. What is your e-mail so I can send them to you?

[mid-tn-mustang]

Thanks, if you could send the pictures to the address belwo I would really appreciate it. By the way, I found the piece that goes up in the hood so I am looking for what you might have on the latch especially including the vertical piece that I think is the hood latch support brace.
creddick@ksise.com

[Tamras70]

Do you have the moulding piece that runs across the top of the windshield?

[petec]

Sent you a PM about getting a picture. If you don't receive the PM you can e-mail at pcosky@comcast.net

[dlinebar]

I could use a clock working or not if you have one...PM me if you do.

[69stanggt]

Hi, I need the driver's door glass channel. Weatherstrip can be trashed. Preferably straight, no deep scratches and all welds still intact. Since I'm asking, does your car have moldings or trim on the front edge of the quarter glass?? If so, I would be interested in those pieces too. Please e-mail reply. Thanks in advance.

[redruM]

i need the plastic insert above the glove box, below the dash panel

Brian
940-465-4821

[duff_r27]

Need all the grille trim pieces, do you still have them?

[ritchie rich]

hi i need a right side headlamp ass can u help please call me at 510-579-1971 thanks
rich

[shoes]

looking for the alternator mounting brackets Do you haoppen to have them for the 302.

[emk69]

What about lower radiator Brackets? Still got em?

[rjs69stang]

How about the vinyl top mouldings?

[sizemeanseverything]

Would you consider cutting out removing the shock towers and complete firewall?

[jordan]

The car it taking up space in my parents garage and I really hate to get rid of it but that is what it is coming down to. I hope once i graduate i will be able to try again and find another project to work on.

[foothilltom]

Hi, there's many pages of replies, so apologies if you've already responded to the parts I need. Which are:

* Hood (straight, rust free)
* Both light buckets
* Dash Pad

Thanks!
Tom

[Pakrat]

Glad you got my message over at Stangnet Tom, welcome aboard!

[Blich123]

Do you have the trim clips for the front windsheild molding at the bottom...also do you have the latch rods and internal parts for the passenger door latch and lock?

[Ignacio]

Im interested in the GearBox bellhousing. PM sent.

[KIWITHUNDER]

Hi there I'm interested in the passenger side and also the dash plastic lower extension piece and lastly the e-brake cable holders from the underside. Let me know please and am available 720 883-6571 Thanks